多槽手動超聲波清洗機與單槽設備非常大的區別在于 “分步”與“協同” 。它將原本在一個槽內完成的全部清洗流程，分解到多個獨立槽體中逐步完成。

The biggest difference between multi slot manual ultrasonic cleaning machine and single slot equipment is "step-by-step" and "collaborative". It decomposes the entire cleaning process that was originally completed in one tank into multiple independent tanks to gradually complete.

典型的配置是3-6個獨立槽體。每個槽體可以分別注入不同介質——清水、專用清洗劑、防銹液、純水等。由此形成完整的清洗鏈條：

A typical configuration is 3-6 independent tank bodies. Each tank can be filled with different media - clean water, specialized cleaning agents, rust inhibitors, pure water, etc. Thus forming a complete cleaning chain:

預洗槽是第一道關卡。采用60℃左右的堿性清洗劑，通過循環噴淋或簡單浸泡，去除工件表面90%以上的切削液、防銹油等大分子污染物。這一步雖然看似簡單，卻能大幅減輕后續主洗槽的負擔。

The pre wash tank is the first level. Using alkaline cleaning agent at around 60 ℃, more than 90% of large molecular pollutants such as cutting fluid and rust proof oil on the surface of the workpiece are removed through circulating spraying or simple soaking. Although this step may seem simple, it can significantly reduce the burden on the subsequent main washing tank.

主洗槽是核心環節。配置40kHz左右的超聲波換能器，產生強烈的空化效應。清洗液在超聲波作用下形成微射流，能深入0.1mm以下的盲孔和細微縫隙中清除金屬碎屑和頑固污漬。主洗槽的清洗時間、超聲波功率均可根據工件污染程度手動調節。

The main washing tank is the core link. Configure an ultrasonic transducer with a frequency of around 40kHz to generate strong cavitation effects. The cleaning solution forms a micro jet under the action of ultrasound, which can penetrate into blind holes and fine gaps below 0.1mm to remove metal debris and stubborn stains. The cleaning time and ultrasonic power of the main washing tank can be manually adjusted according to the degree of workpiece contamination.

漂洗槽負責“收尾”。使用去離子水或純水，采用三級逆流漂洗方式，將電導率控制在5μS/cm以下。這一步的目的是有效清除工件表面殘留的清洗劑，避免水漬和二次污染。

The rinse tank is responsible for "finishing". Use deionized water or pure water, and use a three-stage countercurrent rinsing method to control the conductivity below 5 μ S/cm. The purpose of this step is to thoroughly remove the residual cleaning agent on the surface of the workpiece, avoiding water stains and secondary pollution.

烘干槽完成非常后工序。采用紅外輻射與熱風循環組合的方式，使工件表面水分快速蒸發。快速干燥不僅能防止氧化生銹，還能避免水漬殘留影響產品外觀。

The drying tank completes the final process. By combining infrared radiation with hot air circulation, the surface moisture of the workpiece is rapidly evaporated. Fast drying not only prevents oxidation and rusting, but also avoids the impact of water stains on the appearance of the product.

多槽設計的核心優勢在于靈活換液。面對不同污染物，操作者可以在主洗槽中更換對應的清洗劑——機械零件的切削油污染用中性除油劑；電子元件的助焊劑殘留用專用環保清洗劑；醫療器械的生物污漬用消毒型清洗液。這種針對性換液大幅提升了清潔效率。

The core advantage of multi slot design lies in flexible liquid exchange. Faced with different pollutants, operators can replace the corresponding cleaning agent in the main washing tank - neutral degreaser for cutting oil pollution of mechanical parts; Special environmentally friendly cleaning agents are used for residual soldering flux in electronic components; Disinfectant cleaning solution for biological stains on medical devices. This targeted fluid change greatly improves cleaning efficiency.

同時，獨立槽體設計有效避免了交叉污染。每個槽體獨立儲液，清洗不同批次或不同材質的工件時，可快速排空舊液、注入新液。前序清洗的污漬不會混入后續環節，尤其適合精密光學元件和醫療器械等高潔凈度要求的清洗場景。

Meanwhile, the independent tank design effectively avoids cross contamination. Each tank independently stores liquid, and when cleaning workpieces of different batches or materials, old liquid can be quickly emptied and new liquid can be injected. The stains from the previous cleaning process will not mix into the subsequent steps, especially suitable for cleaning scenarios that require high cleanliness, such as precision optical components and medical devices.

本文由多槽手動超聲波清洗機友情奉獻.更多有關的知識請點擊:http://www.sflrw.com真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from a multi slot manual ultrasonic cleaning machine For more information, please click: http://www.sflrw.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.